Search Results for 10-560663

upto 10 Gb/sec METRAV High Power current carrying capacity upto 30 A 48 pair cable connector . LEVEL 3: CHIP CARD ACCEPTOR LEVEL 1: CHIP TO PACKAGE LEVEL 3: LEVEL 3-. BOARD 10 MEZZANINE BOARD."' BACK PANEL TO DAUGHTER BOARD LEVEL 2: SOCKET TO BOARD LEVEL 5: SUBASSEMBLY 10 1/O PORT LEVEt 6: SYSTEM TO SYSTEM LEVE 4: SSEMBLV TO

Created Date: Wed Jan 17 10:01:17 2001

3.54 x 1.56 x 1.10 in. Weight: Approx. 0.15 kg / 0.33 lb. Environmental; Operating temperature range-30 °C to +60 °C: Ordering Designations. Model Product No. PRO-PM2-2/70-1W-N(f)-N(f) 210000972: Add to quote: Typical response curve. The maximum Tx FWD DC voltage can be adjusted, if necessary.

RF Connector MHF I LK Right Angle Plug to SMA Straight Jack Bulkhead Rear Mount 1.13 mm 50 Ohm 400 mm

RFS Technologies designs and manufactures premium-quality cable and antenna solutions for wireless, public safety, distributed antenna system (DAS) and other telecom markets in North America. As an Amphenol company, we’re part of a global powerhouse in high-technology, interconnect, sensor and antenna solutions that’s enabling the electronics revolution across almost every industry. Our ...

10 ap-116-4 1 spring 302 stainless steel 11 ap-116-6 1 stud anodized aluminum alloy part # cable dia bushing ap-176-01 .165± .010 ap-116-17 ap-176-02 .228± .010 ap-116-18 ap-176 .250± .010 ap-116-8 ap-176-04 .2905± .010 ap-116-19 table #1 mnf l smith 5/22/95 l smith 5/22/95 notes: 1) unless otherwise specified, connector meets all

Created Date: 10/6/2004 10:37:07 AM

T EMPOSONICS® R SERIES SPECIFICATIONS 550574 D PARAMETER SPECIFICATION Measured variable: Displacement Resolution: Up to 0.002 mm (0.00008 in.) Non-linearity: < ± 0.01% of full stroke or ± 0.04 mm (0.0016 in.), whichever is greater* Repeatability: < ± 0.001% of full scale or ± 0.0025 mm (0.0001 in.), whichever is greater

10 13 18 21 39 L Line F SolderCup L Line F SolderCup IfnecessarycontactMartecfor moreinformation 48 Ø.04 62 Ø.062 BodyMaterial BodyDesign SeePinPattern PinTerminations LeftSide PinTerminations RightSide SpecialModifications PinDiameter. 14 HermeticInterconnectSolutions Deviations

6 Step 10: Repeat steps 7 and 8 and 9 to assemble another contact assembly. Step 11: Pull one of the wires out and load. Crimp the Rear Shield (Part 5). Step 12: Repeat step 11 to assemble another Rear Shield. Notes: The recommended crimp sizes are only for reference. The customer should adjust them according to cable specification and crimp ...

Home - Amphenol Australia

Power up is less than 5 seconds. Analog 4-20 output is stable in less than 10 seconds. This device has no special requirements for the reset and power-down process. 13.2. Command Response Times Minimum -15ms Typical -25mS Maximum -75mS 13.3. Channel update time period Typical -250mS 13.4. Non-Volatile Memory

configuration 1 & 5 configuration 2 & 6 • pre-cold figure-i tail indicator configuration 3 a 7 configuration 4 & 8 • pre-coiled

150 W base station duplexers. Both the ¼ λ models and the ¾ λ models are continuously tunable from 406 MHz to 470 MHz. Low insertion loss due to silver-plated, temperature compensated resonator elements in high-Q 40 x 40 mm cavities.

Hermetically sealed (1 X 10-6 cc/sec leakage rate) arrangements are also available. DESIGN FEATURES OF AQUACON SERIES CONNECTORS 1. Corrosion resistant aluminum bronze coupling nut and stainless steel sleeve 2. Hermetic and non-hermetic inserts in MIL-DTL-38999 patterns. Glass or hard dielectric material.

shown with grid cap shown without grid cap 1 1 2 2 a a b b code ident. no. 52681 dwg. no. scale: sheet drawn checked engineer title unless otherwise specified tolerances are:

• Normalized Output (above 10%) : ± 16° *Condition : Distance of IR Point Source to Reflector : 170mm. Outline of Module and Pin Arrangement [unit:mm] Module Circuit C1 C2 C3 C4 C5 R1 R2 R0 R3 R4 R5 R6 R8 RG2 Variable RG3 Variable RG4 Variable RG1 Variable OP1. AAS-920-594A-03/2014

1 1 2 2 3 3 4 4 a a b b code ident. no. 52681 dwg. no. scale: sheet drawn checked engineer title unless otherwise specified tolerances are: dimensions in millimeters

We would like to show you a description here but the site won’t allow us.

10 dB . Typical response curve - 1 dB. 1 dB . Mechanical Outline for FME(m) All dimensions are given in mm [in.] Mechanical Outline for BNC(f) or SMA(f) All dimensions are given in mm [in.] Ordering Designations. Model Product No. BPF 146-174 FME(m) 200002601: Add to quote ...