Search Results for burst oc spray instructions

%PDF-1.4 %âãÏÓ 719 0 obj > endobj xref 719 67 0000000016 00000 n 0000002177 00000 n 0000002336 00000 n 0000008303 00000 n 0000008598 00000 n 0000008712 00000 n 0000044430 00000 n 0000044729 00000 n 0000045044 00000 n 0000045349 00000 n 0000084943 00000 n 0000085228 00000 n 0000123763 00000 n 0000124076 00000 n 0000124512 00000 n 0000167040 00000 n 0000167359 00000 n 0000167684 00000 n ...

bserve the front insulator’s keyway. When the inner pin assembly is held in the verti cal position (with inner pin contacts on top), the inner pin contact with the insulator key way to its left will be positioned at the “9 o clock” orientation position, when viewing the pin as sembly from the mating end (for inner socket contacts, the insulator ...

Ends must be cut cleanly and at right angles to the axial plane of the cable. The cable must not be deformed while making cuts. Hot wire stripping is recommended. 1. Slide shield crimp sleeve back over cable jacket. 2. Flare shield as illustrated and strip cable dielectric. C Flare shield as illustrated and strip cable dielectric. D/ 1.

Step 1 Place nut, washer (when supplied) and gasket over cable and strip jacket to dimension a shown in table above. Step 2 Comb out braid and fold out. Trim insulation off center conductor to dimension c shown in table above. [For RG-62, 71 and 210/U cable, trim an additional .032"(0.8mm) of insulation off center conductor and add bushing.]

5. cable assembly instructions a. trim cable as shown. b. solder cable center conductor to contact. c. insert cable with ptfe insulator entering connector and braid over knurl. d. crimp ferrule with amphenol tool 227-944 and die set 227-1221-57 closure 'a', .213" hex die. use m22520/1-15 positioner. 6. shows cable entry dimensions.

%PDF-1.7 %µµµµ 1 0 obj >/Metadata 1730 0 R/ViewerPreferences 1731 0 R>> endobj 2 0 obj > endobj 3 0 obj >/ExtGState >/XObject >/ProcSet[/PDF/Text/ImageB/ImageC ...

%PDF-1.4 %âãÏÓ 253 0 obj > endobj xref 253 85 0000000016 00000 n 0000002534 00000 n 0000002678 00000 n 0000003489 00000 n 0000003800 00000 n 0000004113 00000 n 0000004344 00000 n 0000009807 00000 n 0000010108 00000 n 0000010367 00000 n 0000017110 00000 n 0000017419 00000 n 0000024629 00000 n 0000024770 00000 n 0000025061 00000 n 0000025613 00000 n 0000033267 00000 n 0000033707 00000 n ...

Routine calibration of sensors and associated instrumentation is necessary to maintain measurement accuracy. We recommend calibrating on an annual basis, after exposure to any extreme environmental influence, or prior to any critical test.

Step 2: Wire cutting and stripping. Note: No sharp burrs after crimping, and single copper wire cannot be exposed, if it has, it must be cut out. Note: When hearing a click and handing gently pull, then it isn't quit, so it shows that assembly is OK.

instructions located in the manual. This symbol indicates safety, earth ground. Manual 21354 Rev E ECN 50523 PCB工业监视和测量设备 - 中国RoHS2公布表 PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table 部件名称 有害物质

Contact, Pin, Coaxial Type LJT-R, TV-R (MIL-DTL-38999 Series I & III) Installation Instructions See table for coaxial cable recommended, tool selec tor settings, crimping tool and positioner information. A 1. The contact incorporates a piggyback grommet seal.

6.0 OPERATING INSTRUCTIONS 10 7.0 CALIBRATION INSTRUCTIONS 12 8.0 OPTIONS 15 Figure Page 1 Series 8159 Front Panel View 2 2 Series 8159 Rear Panel View 3 3 Panel Mounting Cut-Out Dimensions 3 4 Transducer Wiring 4 5 Input/Output (I/O) Wiring 5 6 Location of Jumpers and Potentiometers (Top View) 6 ...

With your personal safety in mind, this manual lists important safety precautions first, then covers installation, operation, maintenance, troubleshooting, warranty, and customer service information.

Slide crimp bushing, large diameter end first, over cable braid until cable jacket butts inside shoulder of crimp bushing. 1. Flair cable braid back over crimp bushing as illustrated to expose inner wires. Trim excess cable braid. 2. Cut off any inner braids, wraps or cable fillers as close to outer cable braid as possible. 3.

%PDF-1.6 %âãÏÓ 268 0 obj > endobj 299 0 obj >/Filter/FlateDecode/ID[06AA73462B934C428407FEA73E89C204>0AA3757D04DCAC4EBFED538533E0C16D>]/Index[268 56]/Info 267 0 R ...

Installation Instructions See table on reverse side for coaxial cable recommended, stripping dimensions, tool selec- tor settings, crimping tool and positioner information.

Contact, Socket, Coaxial Type LJT-R, TV-R Crimp (MIL-DTL-38999 Series I & III) Installation Instructions See table on reverse side for coaxial cable recommended, stripping dimensions, tool selec-tor settings, crimping tool and positioner information. A 1. The contact incorporates a piggyback grommet seal.

Installation Instructions (General Insertion and Removal) for Quadrax Contact Assembly with sealing and alignment boot. For ARINC Connectors. Contacts are to be inserted by hand. Insert contact assembly into the proper grommet hole. Con-tact must be aligned with the hole and not inserted at an angle.

Amphenol Aerospace has developed a new Corrosion Ingress Seal for D38999 Series III-style plug connectors which will significantly increase mated pair protection against salt spray and corrosive atmospheres.

Amphenol Aerospace announces a new, durable REACH/RoHS compliant plating for aluminum connectors, called AP-93, which outperforms Cadmium and exceeds 1000 hour salt spray requirements. AP-93 is available under the Amphenol D38999 Series III service class designator “DS”.