Search Results for dc motor with rpm adjustment
PdM & Process Monitoring | PCB Piezotronics
PCB ® manufactures sensors used by design engineers and predictive maintenance professionals to test and measure vibration, pressure, force, acoustics, load, and shock in research and development as well as industrial applications.. Divisions of PCB
Model 201B03 | PCB Piezotronics
Supplied: 080A82: Assembly lubricant (for Series 201-207 force rings) 1: 081A11: Mounting stud, 10-32 x 0.730", BeCu for Models 201B01, 201B02, 201B03, 201B04, 201B05, 211B & 201B76
DC RESPONSE ACCELEROMETER - PCB
3711F11200G DC RESPONSE ACCELEROMETER Revision: A ECN #: 53791 Performance ENGLISH SI Sensitivity(± 3 %) 6.75 mV/g 0.69 mV/(m/s²) [1] Measurement Range ± 200 g pk ± 1,960 m/s² pk Frequency Range(± 5 %) 0 to 1,500 Hz 0 to 1,500 Hz Frequency Range(± 10 %) 0 to 2,500 Hz 0 to 2,500 Hz Resonant Frequency 11.8 kHz 11.8 kHz [2]
Model 2222C | PCB Piezotronics
Model 2222C:Accelerometer, PE, 1.4 pC/g, -100°F to +350°F, isolated, adhesive mount, side connector, 0.5 grams
Model 356A14 | PCB Piezotronics
Model 356A14:Triaxial ICP® Accel., 100 mV/g, 50 g, 0.5 to 5 kHz, 1/4-28 Side Conn., 10-32 Female, Ti Housing
Model J320C33 | PCB Piezotronics
Model J320C33:ESS high sensitivity, quartz shear ICP® accel, 100 mV/g, 1 to 4k Hz, 10-32 side conn. (to +325 F) ground isolated
Model HTTLD356A15 | PCB Piezotronics
Model HTTLD356A15:Triaxial, high sensitivity, ceramic shear ICP® accel., 100 mV/g, 2 to 5k Hz, titanium hsg, 4-pin conn., TEDS 1.0, to +325F
Product Finder - Lutze Inc.
LUTZE Inc. 13330 South Ridge Drive • Charlotte, North Carolina 28273 • USA Phone: 704-504-0222 • Fax: 704-504-0223 • E-Mail: info (at) lutze.com
Display Features and Modes - amphenol-sensors.com
The sensor is shipped with a 6V DC, 500 mA AC/DC adapter. To use the adapter, connect the plug into the back of the monitor and plug the transformer into any standard wall outlet. Note: It is important to use the adapter supplied with the Telaire 7001. Using the wrong adapter may cause damage to the monitor. Also, the battery operation will
Model TLD352C04 | PCB Piezotronics
Model TLD352C04:General purpose, ceramic shear ICP® accel., 10 mV/g, 0.5 to 10k Hz, 10-32 top conn., TEDS 1.0
12V/12V-18A (220W) Isolated DC-DC Converter - Gemeco
Support. Cables & Adapters. Mix and Match Cables 1kW; Mix and Match Cables 600W; Mix and Match CHIRP Cables; Transducer Identification. B744V/VL Newer Version
Model 3122-01A Rotary Torque, Shaft-Shaft, High Speed, Low ... - PCB
Model Number 3122-01A ROTARY TORQUE, SHAFT-SHAFT, HIGH SPEED, LOW CAPACITY Revision: A ECN #: 37309 Performance ENGLISH SI Measurement Range(Full Scale Capacity) 8.85 in-lb 1 Nm Sensitivity(output at rated capacity) 1.5 mV/V 1.5 mV/V [4]
Model 039275-51501 PCB L&T Rotary Torque Angle Transducer, w/Auto-ID ...
regulated DC or AC excitation is applied between A and B of the bridge. When torque is applied to the transducer, the Wheatstone Bridge becomes unbalanced, producing an output ... Recommended Max RPM ¼-in Drive … 5000 3/8-in Drive … 2500 ½-inch Drive … 2500 ¾-in Drive … 2000 1-in Drive … 1000
Amphenol PCD Shenzhen
dc 12v elock single core wire for ac evse outlet only nevdca12velockl0500hs1. dc 12v elock single core wire for ac evse outlet only p01bp00261. tpa for hvslp1000022adh6 p01bs00134. signal contact p08b004141. mcs vehicle inlet 10pin signal connector cable assembly pdc02xxxxxx. the pdc connector converts 2-pin input into a 4-pin output. ...
Fluid Flow Monitor - gemeco.com
Features FFM100 converts a variety of flow senders (e.g., fuel, water, etc.) to NMEA 2000® Network Data. All flow senders ordered separately depending on application (i.e., single fuel flow sender for gas engine, dual fuel flow senders for diesel engine, water flow sender for sea water, etc.)
Model 640B72 4-20 mA Output Velocity Sensor Installation and ... - PCB
Figure 2 – wiring: loop powered Figure 3 – wiring: loop powered/DC source If using a standard DC power supply, install either an ammeter and/or load resistor in line with the return connection Pin 3. The resistor will generate a DC voltage that is proportional to current by: V = IR If R = 500 and I = 6mA, then V = 3Vdc Note:
Model 626B01 | PCB Piezotronics
Model 626B01:Low freq., industrial, ceramic shear ICP® accel, 100 mV/g, 0.2 to 10k Hz, top exit, 2-pin conn., frequency sweep ISO 17025 accredited cal
RF Connector - Amphenol Antenna Solutions
Frequency Range DC-3 GHz Return Loss ≥ 30 dB Insertion Loss ≤ 0.05 dB Intermodulation (2x43 dBm) ≤ -166 dBc Insulation Resistance ≥ 5000 mΩ Work Voltage 2500 V Conductor Resistance Outer Conductor < 0.1 mΩ Inner Conductor < 1.0 mΩ Impedance 50Ω Environmental Characteristics Temperature Range -40° C to +85° C (-40° F to +185° F)
NovaSensor NPP-301 Pressure Sensor FAQ's - amphenol-sensors.com
pin 2 and the negative lead to pin 6. Set the voltmeter to read DC voltages with a resolution of 1 mV or 0.001 volts. At sea level, and with 3 volts powering the sensor, the NPP-301A-100A (15 psia, 100 kPa) will read approximately 0.06 volts. The NPP-301A-200A (30 psia, 200 kPa) will read 0.03 volts under the same conditions.
Product Finder - Lutze Inc.
LUTZE Inc. 13330 South Ridge Drive • Charlotte, North Carolina 28273 • USA Phone: 704-504-0222 • Fax: 704-504-0223 • E-Mail: info (at) lutze.com