Search Results for ferrule-174
ferrule | Amphenol Global Search | Amphenol
ferrule step 1. all parts of connector are shown. step 2. strip the cable inner conductor, braid and as step sloe ferrule onto cable. step a. insert acor into brad ano dielectric. then ferrule over proper tool. step s. solder to the of main soar. then screw into 't stops. if press cap is pro'oed. press into place_ connector car oratlon angle crimp
262101 | Amphenol Global Search | Amphenol
RF Connector MMCX Straight Crimp Plug RG-174 RG-188 RG-316 Times LMR-100A 50 Ohm. Downloads. 262101 STP 3D Model (Size: 58 kb ) 262101 PDF Customer Drawing (Size: 67 kb) Assembly Instructions 3 Piece Crimp-Solder (Size: 44 kb) Product Life Cycle. ... Then slide the FERRULE onto cable. Insert the MAIN BODY into braid and dielectric. Slide the ...
RIGHT ANGLE PLUGS & CRIMP TYPE - Amphenol RF
919-104P-51AX 50µ MCX Angle Plug 174, 188, 316 .128 (3.25) CTL -13 .337 .133 .106 ... ferrule over braid and crimp using hex die shown in table above. Step 3 Solder center conductor into contact. Step 4 Insert cap into body and dimple or lightly punch center of cap for retention in body.
Assembly Instructions-C53 Amphenol SMA
322 Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com Assembly Instructions-C53 Amphenol® SMA(continued) Step 1 Step 2 Step 3 Step 2 & 3 for angle plugs
Assembly Instructions-C26 Amphenol BNC
assembly so that inner ferrule portion slides under braid. Push cable assembly forward until contact snaps into place in insulator. Slide outer ferrule over braid and up against connector body. Crimp outer ferrule using Die Set Cavity specified in table above. cable dielectric must butt insulator outer ferrule should butt here crimp here
euromicron | Amphenol Global Search | Amphenol
FERRULE-174 | Amphenol Global Search | Amphenol For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100" (2.5mm) as shown. Before attaching center contact, slide TFE sleeve (not shown) over cable dielectric and under braid.
FAKRA Cable Assemblies - Amphenol RF
featuring the popular RG-58 and RG-174 flexible cables. These cable assemblies feature a variety of connector configurations and are available in a number of standard length options from 12 inches to five meters which makes them ideal for a wide range of automotive development applications. These cable assemblies utilize industry standard FAKRA
Assembly Instructions-C26 Amphenol BNC
assembly so that inner ferrule portion slides under braid. Push cable assembly forward until contact snaps into place in insulator. Slide outer ferrule over braid and up against connector body. Crimp outer ferrule using Die Set Cavity specified in table above. cable dielectric must butt insulator outer ferrule should butt here crimp here
RIGHT ANGLE PLUGS & CRIMP TYPE
919-104P-51AX 50µ MCX Angle Plug 174, 188, 316 .128 (3.25) CTL -13 .337 .133 .106 ... ferrule over braid and crimp using hex die shown in table above. Step 3 Solder center conductor into contact. Step 4 Insert cap into body and dimple or lightly punch center of cap for retention in body.
RF Connector Assembly Instructions - Amphenol RF
Crimp connectors feature a ferrule that crimps onto a cable's braid. The connector's center contact can sometimes be crimped into the center conductor or soldering may be required. If you need to purchase crimp tooling including crimp frames and die sets, please visit our Tools Category Page. If you're assembling a crimp connector, the ...
Assembly Instructions-C57 Amphenol SMA
TYPES FOR RG-174 & RG-179 CABLE GROUPS Step 1 Slide heat shrink tubing and outer ferrule onto cable. Strip cable jacket, braid and dielectric to dimensions shown in table above. All cuts are to be sharp and square. Do not nick braid, dielectric or center conductor when cutting. Tin center
heat shrink | Amphenol Global Search | Amphenol
FERRULE-174 | Amphenol Global Search | Amphenol Step 3 Install inner ferrule of body assembly over cable dielectric and under braid. Place outer ferrule against body and crimp with tool 227-944 (M22520/5-01) and die set shown in table above. Place heat shrink tubing over crimp ferrule, against body, and apply heat.
74868 - Amphenol RF
3. slide ferrule over the braid until it rests on the rear surface of the body. crimp the ferrule in place using the applicable hex die as shown in the table on sheet 1 based on the part number. the ferrule should be crimped as close to the body as possible. the crimp should withstand an axial pull of 110n for 5 seconds.
Assembly Instructions-C26 Amphenol BNC
assembly so that inner ferrule portion slides under braid. Push cable assembly forward until contact snaps into place in insulator. Slide outer ferrule over braid and up against connector body. Crimp outer ferrule using Die Set Cavity specified in table above. cable dielectric must butt insulator outer ferrule should butt here crimp here
MTC-HD – High Density MT Ferrules with 6 Insert Arrangements
Increasing the density for rugged environments including military aerospace, commercial aircraft, ground-based radar, or industrial applications. The first generation of MT38999 supported two shell sizes and up to 24F ferrules, whereas MTC-HD offers an additional six insert arrangements and up to 48F or even 72F ferrules!
FAKRA CONNECTOR SERIES
Contact Crimp Ferrule Housing O Ring Right Angle Jack Straight Plug Heat Shink Tubing Crimp Ferrule Male Contact Body Subassembly Crimp Ferrule Heat Shrink Tubing O Ring ... 3FA1MXSJ-C01E0 RG-174/DACAR 462 349-50832 349-50750 3FA1-NXSJ-C01E0 RG-174/DACAR 462 349-50832 349-50750
3-PIECE CRIMP ANGLE PLUGS & BULKHEAD JACKS - Amphenol RF
outer ferrule bushing male contact plug body assembly used with RG-62, 71, 210 cable only Step 1 For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100"(2.5mm) as shown. Before attaching center contact, slide metal spacer/TFE sleeve
Assembly Instructions-C26 Amphenol BNC
assembly so that inner ferrule portion slides under braid. Push cable assembly forward until contact snaps into place in insulator. Slide outer ferrule over braid and up against connector body. Crimp outer ferrule using Die Set Cavity specified in table above. cable dielectric must butt insulator outer ferrule should butt here crimp here
CRIMP TYPE ANGLE PLUGS & ANGLE BULKHEAD JACKS - Amphenol RF
903-289P-51A 50ΩSMB Angle Plug 174, 179, 187, 188, 316 .128(3.3) 227-1221-03 Cav. A .390(9.9) .150(3.8) .050(1.3) ... ferrule over braid and crimp using hex die shown in table above. Step 3 Solder center conductor into contact. Step 4 Insert cap into body and dimple or lightly punch center of
MT38999 Multi-Channel Connectors with MT Ferrules
Ferrules are available in either 12-fiber or 24-fiber versions, in multi-mode PC, single mode PC, and single mode APC configurations; 2 arrangements are available -- shell size 11 with one ferrule, and shell size 21 with four ferrules; Technical Information