Search Results for floor function matlab
Noise Floor Calculations in Acoustic Testing - PCB
Dr. Andrew Barnard shows how use Noise floor calculations to when testing to discover sources of unwanted noise when designing products. This is typically used in testing for the automotive industry and computer components such as disk drives.
IMPACT AND DROP TESTING - PCB
calculate the results. A simple test method of measuring impact force versus displacement, and then integrating for the area under force-displacement curve provides an. utput in energy units. However, what force output could the engineer expect to measure .
Pros and Cons of an Analog Bandpass Filter vs. Digital Filter - Q Microwave
To find the right filter for your application, you must consider numerous factors – such as operating frequency range, signal-to-noise ratio, power consumption, and the need for reconfigurability. Then, weigh these variables against the specific requirements of the RF application in question.
Amphenol Connector Basics Terminology Guide
Interchangeable - Characteristic of connectors in which one manufacturer’s connector can be replaced by the connector of another manufacturer and provide the same function in the same panel space as the connector it is replacing.
Introduction to Piezoelectric Force Sensors | PCB Piezotronics
The following information presents some of the design and operating characteristics of PCB force sensors to help you better understand how they function, which in turn, will "help you make better dynamic measurements". Figure 1 illustrates the cross-section of a typical quartz force sensor.
Integrated IR Application Note 1 - SGX Sensortech
AN1 - Integrated IR Application Note Page 3 of 35 Whilst SGX Europe sp. z o.o has taken care to ensure the accuracy of the information contained herein it accepts no responsibility for the consequences of any use
Bulkhead-Style Fiber Panels - amphenol-ns.com
Amphenol Network Solutions’ LCX line of bulkhead-style panels provide all of these features and capabilities. Here is a look at where each of the key components of the product line fits best in today’s network applications. Many applications require the termination of just a handful of fibers.
Data Sheet E-Series EP/EL Analog (Doc Part No. 551245)
Robust, non-contact and wear free, the Temposonics® linear position sensors provide the best durability and precise position measurement feedback in harsh industrial environments. Measurement accuracy is tightly controlled by the quality of the waveguide manufactured exclusively by Temposonics.
White Papers | PCB Piezotronics
Collecting Vibration Data with a USB Digital Accelerometer and an Android Phone While Analyzing with MATLAB
Temposonics MH-Series MH4 Plus Analog 551958
Temposonics® MH sensors are successfully used in front axle and articulated frame steering cylinders, hydraulic jacks and in steering systems for hydraulic units on agricultural and construction machinery. MH sensors are designed for mobile machines and intended for IN cylinder use.
Instruction Manual Amphenol - PROTIMETER
Moisture measurements can be taken using the integral pin electrodes. When used with the temperature probe, the moisture measurements are automatically corrected with respect to temperature. This feature is particularly relevant for users testing wood that is significantly above or below. 20°C (68°F).
Frequently Asked Questions | Protimeter Moisture Meter Function
If you place the piece of timber on the concrete floor and leave it to equilibrate, the wood will absorb moisture from the concrete until it has reached approximately 25%. This system of measurement is known as WME (Wood Moisture Equivalent) and is used globally for moisture diagnosis in buildings.
Amplitude Linearity Measurement and Damped Accelerometer - PCB
Amplitude linearity is a measure of how linear the output of an accelerometer is over its specified amplitude range. It is sometimes called amplitude non-linearity, since it specifies the deviation from perfect linearity. Manufacturers of accelerometers typically rely on several methods to measure non-linearity of the device.
Board-Level Connectors | Products - Amphenol
FLTStack 0.50mm is a floating type Board-to-Board (BTB) connector designed to operate a minimum of ±0.50mm floating range in the XY directions. It features a self-cleaning function, vibration resistance, and self-alignment for easier mating. In addition, it supports up to 3Gb/s communication data rates.
Control and Communication in Robotics: Enabling Seamless Connectivity ...
In this blog, we will explore the significance of these functions in robotics and how Amphenol's innovative connectors play a pivotal role in enabling seamless connectivity within robotic systems. In robotics, control refers to the ability to regulate the movement and behavior of robotic components with precision and accuracy.
AEROSPACE GROUND TEST - PCB
Ground testing of a new aircraft design or an aircraft that has undergone significant structural modification, is a prerequisite before any flight-test program can begin.
OUR COMPANY - amphenol-socapex.com
Different technologies are used in order to ensure the following functions: - EMI shielding - cable retention - sealing This large choice of rear accessories provides you with the right solution for your connector/backshell interconnection. GENERAL CHARACTERISTICS Main features Description • Shell material - Aluminium alloy - Marine bronze
IMAC2001 368 A Smart Sensor Signal Conditioner - PCB
What is required in order to effectively deploy dynamic signal solutions to the production floor on a more cost-effective basis is either smarter sensors, or smarter signal conditioning. The general requirements of this signal conditioning are as follows:
PCB > Learn > Videos
3425 Walden Avenue Depew, NY 14043. Sensorline SM 716.684.0001. info@pcb.com +1 800-828-8840
Understanding Safety Integrity Levels - PCB
Safety Instrumented Systems [SIS] or Safety Instrumented Function [SIF] operating independently of the E/E/PE system) to minimize hazards and resulting risk levels. The analysis process starts long before a single component goes on to the manufacturing floor, beginning when the