Search Results for keyhole upper stripped

Flex Connector, 1.00mm Pitch, Height 2.00mm, Right angle, Slider type, ZIF, Upper contact, 20 position , Without MYLAR

Amphenol’s Uni-Boot Duplex Metal Bodied LC is precision manufactured from both machined and die cast alloy materials. It provides an LC compatible connector able to withstand abuse in tough military, industrial, and science applications.

Strip the outer red Teflon jacket, 0.5 inches, and trim the shield as close as possible to the jacket. Remove all black low noise treatment on the two leads (see the stripping instruction card [74314] for proper lead preparation steps). Clean both leads with alcohol or other approved solvent. See figure 1. Disassemble the connector.

2M804 connectors are the most rugged push-pull micro-miniature circular connectors on the market. Designed for use in soldier-worn tactical equipment deployed by the United States military, these connectors were built to perform.

stripped to equal length. F 1. Carefully splay inner wires perpendicular to the axis of the cable as illustrated. 2. Assemble inner contact over cable center conductor until fully seated against inner wire insulation. Observe center conductor through the contact’s wire in­ spection hole, to make certain conductor is properly positioned. 3.

Model 010P05:4-conductor, shielded, FEP cable, 5-ft, 4-socket plug (AY) to stripped and tinned pigtails. (for use w/ 3711 series accels)

7. Crimp contacts (E) onto stripped wire leads (Figure 3). 8. Insert crimped contacts (E) into connector cavities (F), as shown in Figure 3. Verify contacts are properly sealed once installed. Figure 1 Figure 2 Reference View A Figure 3 284

Model 353B11:High frequency, quartz shear ICP® accel., 5 mV/g, 1 to 10k Hz, 5-44 side conn.

Strip inner wires to expose center conductors as illustrated. All wires must be stripped to equal length. 1. Carefully splay inner wires perpendicular to the axis of the cable as illustrated. 2. Assemble inner contact over cable center conductor until fully seated against in ner wire insulation.

stripped to equal length. F 1. Carefully splay inner wires perpendicular to the axis of the cable as illustrated. 2. BRAIDAssemble inner contact over cable center conductor until fully seated against inner wire insulation. Observe center conductor through the contact’s wire inspection hole, to make certain conductor is properly positioned. 3.

Triaxial amplitude response calibration, from 10 Hz to upper 5% frequency, NIST traceable: 1

stripped to equal length. F 1. Carefully splay inner wires perpendicular to the axis of the cable as illustrated. 2. Assemble inner contact over cable center conductor until fully seated against inner wire insulation. Observe center conductor through the contact’s wire in­ spection hole, to make certain conductor is properly positioned. 3.

iezotronics is an ISO-9001 certified company whose calibration services are accredited by A2LA to ISO/IEC 17025, with full traceability to SI through N.I.S.T. In addition to our standard calibration services, we also offer specialized tests, including: sensitivity at eleva.

Strip inner wires to expose center conductors as illustrated.

Strip inner wires to expose center conductors as illustrated. All wires must be stripped to equal length. F 1. Observe the front insulator’s keyway.

Quartz force sensors are recommended for dynamic force applications. They are not used as 'load cells' for static applications. Measurements of dynamic oscillating forces, impacts, or high-speed compression/tension un-

Strip inner wires to expose center conductors as illustrated. All wires must be stripped to equal length. 1. Carefully splay inner wires perpendicular to the axis of the cable as illustrated. 2. Assemble inner contact over cable center conductor until fully seated against inner wire insulation.

Strip inner wires to expose center conductors as illustrated. All wires must be stripped to equal length. 1. Carefully splay inner wires perpendicular to the axis of the cable as illustrated. 2. Assemble inner contact over cable center conductor until fully seated against inner wire insulation.

All wires must be stripped to equal length. F 1. Carefully splay inner wires perpendicular to the axis of the cable as illustrated. 2. Assemble inner contact over cable center conductor until fully seated against inner wire insulation.