Search Results for tc-400-tm-x

Size (Height x Length x Width) 0.55 in x 0.80 in x 0.55 in 14.0 mm x 20.3 mm x 14.0 mm Weight 0.37 oz 10.5 gm [1] Electrical Connector 1/4-28 4-Pin 1/4-28 4-Pin Electrical Connection Position Side Side Mounting Thread 10-32 Female 10-32 Female Mounting Torque 10 to 20 in-lb 113 to 225 N-cm [5]

Models 356A43, 356A44 and 356A45 are miniature and lightweight triaxial ICP ® accelerometers that are TEDS IEEE 1451.4 enabled. The accelerometers are hermetically sealed and packaged in a 0.4 inch (10.16 mm) titanium cube that weighs 0.15 ounces (4.2 grams). These miniature triaxial accelerometers are available with three sensitivities, 10 mV/g, 50 mV/g or 100 mV/g.

125A 4-Position Demarcation Fuse Panel, ±24V-48V with TFD Holders. Designed specifically to provide a demarcation point for large power feeds between primary distribution and network equipment, Amphenol Network Solutions demarcation fuse panel can handle four loads of up to 125A each.

Size (Height x Width x Length) 0.4 in x 0.4 in x 0.4 in 10.2 mm x 10.2 mm x 10.2 mm Weight(without cable) 0.14 oz 4 gm [1] Electrical Connection Position Side Side Cable Termination 1/4-28 4-Pin Jack 1/4-28 4-Pin Jack Cable Length 5 ft 1.5 m Cable Type 034 4-cond Shielded 034 4-cond Shielded Mounting Thread 5-40 Female 5-40 Female

Model 356A17:Platinum Stock Products; Triaxial, high sensitivity, ceramic shear ICP® accel., 500 mV/g, 0.5 to 3k Hz, aluminum hsg, 4-pin conn.

Every Airmar transducer has a label attached to its cable, located near the top of the transducer or where the cable plugs into the back of the instrument or display. This label contains information that is helpful in identifying the transducer and locating the correct service parts for it.

Three accelerometers can be mounted to the TC series cubes to measure vibration along three orthogonal directions (x,y,z). The cubed design allows free alignment of the x and y axes. FM101 FM102 FM103 FM104 Diameter 0.50 in 0.25 in Height 1.25 in 2.00 in 1.75 in 1.00 in TC1 TC1B TC2 Size 1.0 in 2.6 in Weight 1.27 oz 17.64 oz Mount 10-32 1/4-28 ...

TC Wire Cable / SA 00-1- / Canada 00--01 / exico 001---1 / tpcwire.com eifiations suet to ange For oete seifiations an aaiaiit as our C aes eresentatie or a 55 ower Cable Welding Cable ortable Cord Igniter Wire High Temperature Thermo-Trex® Igniter Wire with Fluoropolymer Jacket Igniter Wire

Size (Height x Length x Width) 0.55 in x 0.4 in x 0.4 in 14 mm x 10.2 mm x 10.2 mm Weight 0.2 oz 5.5 gm [1] Electrical Connector 8-36 4-Pin 8-36 4-Pin Electrical Connection Position Side Side Mounting Stud Stud Mounting Thread 5-40 Female 5-40 Female [2] All specifications are at room temperature unless otherwise specified.

Pressure port: ISO 6149 Hexagon housing SW27 with M14 x 1,5 O-ring: 11,3 x 2,2 mm NBR 80: Electrical installation: Supply Voltage: 12 VDC (tolerance range 9 - 15 VDC) Power drain: < 1 W Over voltage protection (GND-VDC) up to 30 VDC Polarity protection: VDC - GND:

Model 356B20:Triaxial, miniature (4 gm), ceramic shear ICP® accel., 1 mV/g, 2 to 7k Hz, titanium hsg, mini 4-pin conn.

The x-yy portion of the model number designates the type of signal processing and the full-scale range. The signal types are VR or AR for “root-mean square (rms)” signal output and VP or AP for “peak” signal output. The table below summarizes the models and full-scale ranges available. Table 1 – PC420 model numbers for 2 wire output

Electrodynamic Exciter Kit with Horizontal Table. 178 N (40 lbf) pk sine force system. Includes 2075E shaker with 2100E21-400 power amplifier, lightweight horizontal magnesium flexure table, shaker mounting base for vertical and horizontal.

X-Keying* Y-Keying* Z-Keying* U-Keying* * 4 housing sizes with 4 mechanical keying options * Jam-Nut & Cable-to-Cable versions for each layout -USCM Series:USCM 0XX - 001 USCM Connector Arrangements 002: 2 Way 004: 4 Way 006: 6 Way 008: 8 Way 010: 10 Way 012: 12 Way 124: 12+4 Way 016: 16 Way 025: 25 Way ...

Page 4 of 17 a a 1.0 Introduction The concept of intrinsic safety in wiring recognizes that a sufficient concentration of ignitable, flammable or combustible materials will be present, with air or another

Model Number 352B10 ICP® ACCELEROMETER Revision: E ECN #: 42197 Performance ENGLISH SI Sensitivity(± 10 %) 10 mV/g 1.02 mV/(m/s²) Measurement Range ± 500 g pk ± 4905 m/s² pk

Size (Height x Length x Width) 0.30 in x 0.55 in x 0.55 in 7.6 mm x 14.0 mm x 14.0 mm Weight(without cable) 0.18 oz 5.0 gm [1] Electrical Connector 1/4-28 4-Pin 1/4-28 4-Pin Electrical Connection Position Side Side Cable Length 5 ft 1.5 m Cable Type 034 4-cond Shielded 034 4-cond Shielded

4-conductor, low noise, shielded FEP cable, 5-ft, 4-socket plug to (3) BNC plugs (labeled X Y Z) 1: 080A109: Petro Wax, one square, 1" x 1" x 0.25" 1: 080A90: Quick bond Gel (for use with accel adhesive mtg bases to fill gaps on rough surfaces) 1: ACS-1T: Triaxial amplitude response calibration, from 10 Hz to upper 5% frequency, NIST traceable: 1

Ga/Gb Ex db eb IIC T4 X Da/Db Ex tb IIIC T130°C X Zone 0/1, Zone 21 −40 °C ≤ Ta ≤ 75 °C Ga/Gb Ex db IIC T4 X Da/Db Ex tb IIIC T130°C X Zone 0/1, Zone 21 −40 °C ≤ Ta ≤ 75 °C Ga/Gb Ex db IIC T4 X Da/Db Ex tb IIIC T130°C X Zone 0/1, Zone 21 −40 °C ≤ Ta ≤ 75 °C No hazardous area approval KCs (South Korea) Ex d e IIC T4 Ex ...

ICP ® Shock Accelerometers. Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity.