Search Results for amplifier
Model 137A23 ICP® Pressure Sensor Installation and Operating Manual - PCB
Drawing Number: 21168 Revision: NR OPERATION MANUAL FOR FREE FIELD BLAST PRESSURE PROBE Models 137A21, A22, A23 2 For driving long cables (to several thousand feet), use
Vibration Sensor and Accelerometer Accessories
We are your resource for vibration monitoring accessories. We offer a wide assortment of mounting hardware including magnetic sensor mounting bases, mounting pads, studs, isolator bases, fin mounts, and triaxial mounting cubes - along with adhesives and greases.
Introduction to Piezoelectric Pressure Sensors - PCB
The low frequency response of a charge mode pressure sensor is determined by the charge amplifier. The discharge time constant (DTC) of the amplifier that sets the low frequency response can be very long or very short depending on the charge amplifier model used.
CHARGE AMPLIFIERS - PCB
+18 to 28 VDC: Constant Current Excitation. 2.2 to 20 mA: 2 to 20 mA. Output Impedance <10 Ohm <100 Ohm: Output Bias Voltage +12 to 15 VDC +9 to 13 VDC. Output Voltage
Model 421B30 Differential charge amplifier for Dynamic pressure ... - PCB
PAGE 3 Introduction The 421B3X-Series Differential Charge Amplifiers are designed to convert the high-impedance output of a differential, charge-mode piezoelectric sensor to a low-impedance voltage output.
User Manual - AMPHENOL PROCOM
19” Rack-mountable Active Receiver Multicoupler . type . PRO-ARU4G . PRO-ARU8G . User Manual
731A seismic accelerometer and P31 power unit/amplifier Operating guide
90225 Rev D.3 06/12 Page 3 1.0 Introduction The 731A seismic accelerometer and P31 Power Unit Amplifier are a unique state-of-the-art system for the measurement of
VIBRATION FUNDAMENTALS - PCB
Flexibility in adjusting accelerometer output characteristics Extended low frequency response with long time constant charge amps Charge mode - The output of a charge mode accelerometer
Selecting the Correct High Sensitivity Piezoelectric ... - PCB
Figure 2: Material Configurations . Piezoelectric materials produce a high output with very little strain. They have no deflection. This makes piezoelectric sensors rugged and their signal linear over a
Understanding the accelerometer noise specification
83 Progress rive rederic, 2101 Tel: +1 (301) 330 8811 info@wilcoxon.com wilcoxon.com buy.wilcoxon.com Wilcoxon Sensing Technologies Understanding the accelerometer noise specification
Troubleshooting Using Bias Voltage | PCB Piezotronics
Troubleshooting Using Bias Voltage Using Bias Voltage as a Diagnostic Tool. Piezoelectric sensors are dynamic measuring equipment. They use piezoelectric sensing elements to convert or transduce the mechanical phenomena to an electrical signal.
Amphenol Socapex - Connectors, military connectors, circular connectors ...
Rugged solutions tailored to military requirements. Amphenol Socapex's military products are used by a wide range of customers, including defense contractors, military prime contractors, and government agencies.
Model PRM902 | PCB Piezotronics
Model PRM902:1/2" diameter ultra low noise preamplifier with 7-pin LEMO® connector
IPA2008DSL2-RSVFA - Amphenol Broadband Solutions
TRAINING & SUPPORT. Login to the Amphenol Broadband Resource Portal for pre- and post-deployment support. Login
Data Plus IPA2000DSL2-RSVFA MoCA Amplifier Series
Page 3 amphenolbroadband.com | ABS: 800-677-2288 | LATAM: 805-339-9060 | Toll Free: 800-628-4511 DS-65-0209 Rev. 1.1 Data Plus IPA2000DSL2-RSVFA
TNC Connectors - Amphenol RF
Amphenol RF offers a broad range of radio frequency TNC Connectors including industry standard designs and highly engineered Amphenol RF proprietary interfaces. Check product specs & datasheets for a wide selection of TNC Connectors at Amphenol RF online.
CC701 charge converter for charge mode accelerometers
Features. Low noise PiezoFET® amplifier; Converts charge mode transducers to voltage mode; Works with industry standard two-wire system power supply
About | Amphenol Active Optics Products
Amphenol AOP designs and manufactures optical transceivers for the datacom, military and aerospace markets. The team has more than 21 years of proven track record in designing and volume manufacturing optoelectronic products.
Calibration and Repair - PCB
WHY CALIBRATE? Regular calibration validates all relevant performance parameters of your sensor against the original factory specifications. Each calibration is a quality record allowing you to ensure your sensors are functioning properly and enabling you to trend performance over time with confidence in your measurements.
Danmike DM 8350 - AMPHENOL PROCOM
General-purpose microphone amplifier. Adjustable gain 10 → 40 dB. Provides easy “sensitivity-matching” between low-output microphones and transceivers requiring high input level.