Search Results for pt02c-20-41px003

20.6 20.6 20.6 20.6. Amphenol Sine Systems 44724 Morle Drive, Clinton Tonship, M 48036 USA amphenolsinecom 092021 Crimp Contacts, Machined Crimp Contacts, Stamped & Formed Part Number AWG Wire Range (mm²) Plating Part Number AWG Wire Range (mm²) Plating Male Female Male Female

Elevation Beamwidth (3 dB) degrees 21.5° ± 3.0° 20.0° ± 1.5° 19.0° ± 1.8° 15.4° ± 2.2° Electrical Downtilt degrees (x) 2°, 4°, 6° Impedance Ohms 50Ω VSWR --- ≤ 1.5:1 Passive Intermodulation 3rd Order for 2x20 W Carriers dBc < -153 Upper Sidelobe Suppression dB N/A N/A N/A N/A Isolation Intraband dB > 25 Interband dB > 28

Excitation Voltage 20 to 30 VDC 20 to 30 VDC Constant Current Excitation 2 to 20 mA 2 to 20 mA Output Impedance ≤ 200 Ohm ≤ 200 Ohm Output Bias Voltage 8 to 12 VDC 8 to 12 VDC Discharge Time Constant 0.8 to 2.4 sec 0.8 to 2.4 sec Settling Time(within 10% of bias) ≤ 5 sec ≤ 5 sec Spectral Noise(1 Hz) 200 µg/√Hz 1,962 (µm/sec2)/√Hz [1]

MP Common Sizes: 18”x18”x10” 20”x20”x10” 24”x24”x8” 32”x16”x8” 36”x24”x12” 36”x36”x12” Common sizes (HxWxD) represent existing CUBE designs typically stocked by Charles authorized distributors. Custom sizes are available by special order. MP1818 MP2424

Available with integrated backshell technology; Mating endurance of 500 operations for gold plated contacts; Fully intermateable and intermountable with BS 9522 F0017, and MIL-DTL-26482 Series 1 (solder)

Intraband dB > 20 Interband dB > 28 PRODUCT OVERVIEW Frequency Range (MHz) (1x) 696-960 (2x) 1695-2700 (2x) 3300-4200 (1x) 5150-5925 Array ...

Constant Current Excitation 2 to 20 mA 2 to 20 mA Output Impedance ≤ 200 Ohm ≤ 200 Ohm Output Bias Voltage 9 to 16 VDC 9 to 16 VDC Discharge Time Constant 0.24 to 1.0 sec 0.24 to 1.0 sec Settling Time(within 10% of bias) < 3 sec < 3 sec Spectral Noise(1 Hz) 1,200 µg/√Hz 11,772 (µm/sec2)/√Hz [1]

0 to 20 ips pk. 0 to 500 mm/s pk. Displacement Amplitude Range (50 Hz, 10g payload) 0 to 150 mils pk-pk. 0 to 3.8 mm pk-pk. Acceleration Amplitude Range (50 Hz, 500g payload) 0 to 2.5 g pk. 0 to 24.5 m/s

Operating temperature range -20 °C to +60 °C ADDITIONAL DATA RETURN LOSS [dB] 100 - 1000 MHz > 22 dB 1000 - 2000 MHz > 22 dB 2000 - 2500 MHz > 22 dB ATTENUATION FREQUENCY [dB/100m] Max. HF power/W 50 MHz 19.0 150 MHz 29.0 450 MHz 49.0 900 MHz 67.0 1400 MHz 86.0 1800 MHz 96.0 2200 MHz 108.0 2500 MHz 116.0 3000 MHz 126.0 RG 174/U-LL

16 channels with current adjustment within 2 to 20 mA at +18 to +30 volts DC. Refer to PCB Tech NoteTN-32 for more information on signal conditioners and impedance. Do not attempt to power ICP ® sensors with commercially . available power supplies as unregulated current will damage the sensors' internal electronics.

measured @ 20 mA, Green - 565 +/- 7 nm measured @ 20 mA, Red - 625 +/- 5 nm measured @ 20 mA: MECHANICAL PERFORMANCE § Mating connector insetion force: 5.0 lbs. max. § POS Terminals. Mating connector pull retention force: 20 lbs min. § Durability: 750 mating and unmating cycles: SPECIFICATION § Amphenol Product Specification: S6032C

Home - Amphenol Canada

Excitation Voltage 20 to 30 VDC 20 to 30 VDC Constant Current Excitation 2 to 20 mA 2 to 20 mA Output Impedance ≤ 200 Ohm ≤ 200 Ohm Output Bias Voltage 8 to 12 VDC 8 to 12 VDC Discharge Time Constant 0.6 to 2.0 sec 0.6 to 2.0 sec Settling Time(within 10% of bias) <5 sec <5 sec Spectral Noise(1 Hz) 150 µg/√Hz 1472 (µm/sec2)/√Hz [1]

Home - Amphenol Australia

Designed by Amphenol Socapex 4 USB3CFTV C ⌀ ⌀ AMPHENOL SOCAPEX _____ ⌀ ⌀ AMPHENOL SOCAPEX _____ ⌀ ⌀ AMPHENOL SOCAPEX _____ Jam nut receptacle ...

notes: (unless otherwise specified) 1. material: shell: thermoplastic, ul94 v-0. insert: thermoplastic, ul94 v-0. o-ring: silicone rubber. seal gasket: silicone rubber.

20 30 40 50 60-100 200 500 800 1100 1400 1700 2000 Angle (deg) Torque (Nm) Post Yield Zone . 8 On a thread strip failure the decrease in torque will not typically be a vertical drop after the peak torque. A steep downward slope can occur along with the torque value not going to zero. Often times a cyclical wavelike form will be present as in

cost, 2427 VDC, 2- -20 mA constant current supply. Figure 1 schematically illustrates a typical ICP sensor system. PCB offers a number of AC or battery-powered, single or multi-channel power/signal conditioners, with or without gain capabilities for use with force sensors. In addition, many data

(1/4-20 studs, 0.625” spacing) 2x8 position ground bar (1/4-20 studs, 0.625” spacing) equipment compartment battery compartment heat exchanger ac load center battery retainer bracket and battery tray lacing panel generator inlet overheat thermostat removable cover panel with filter screen ac surge suppressor; lt-rl21221abj